Looking for:
Cisco fabric manager download windows 10 |
Installing Cisco MDS NX-OS and Fabric Manager.Cisco fabric manager download windows 10
Cisco Fabric Manager Client is used by datacenter administrators for fabricwide provisioning and to represent the storage network topology map. Cisco Fabric Manager provides centralized Cisco MDS Family and Cisco Nexus Family storage network management services, performance monitoring, federated reporting, troubleshooting tools, discovery, and configuration automation for datacenter. The following table lists the minimum resource required for both, client and server, for Cisco Fabric Manager to work properly.
Size Small Medium Large. Before you install Fabric Manager, you must install a database. Follow the link to install Oracle Database 10g. Run the following script to change the default Oracle admin port and to create a database account. Follow these steps in install Fabric Manager on Windows. Step 9. Select an installation folder on your workstation for Fabric Manager. Click Next. Step Click the radio button for either Install PostgreSQL or Use existing database and enter a database user name and password.
Note that Cisco Fabric Manager has not been officially tested on any bit platforms, only bit platforms are officially supported. However users were able to install Fabric Manager on bit Windows by following these steps:. Step 1.
Open a command prompt cmd. To do this right-click on cmd. This is important. Step 2. Change to your Java directory i. Checked with Java version 1. Step 3. Run the command "Java. On the CD image download, it's in the Software folder. Your command prompt should look something like this, depending on where the Fabric Manager jar file is located:.
Buy or Renew. Find A Community. Cisco Community. Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Showing results for. Search instead for. Did you mean:. All Community This category This board. Installing Cisco Fabric Manager on Windows. Labels: Storage Networking. Sandeep Singh. Resource Requirements The following table lists the minimum resource required for both, client and server, for Cisco Fabric Manager to work properly.
Click the Install Management Software link. Click the Installing Fabric Manager link. Step 4. Step 5. Click the FM Installer link. Step 6. Click Next to begin the installation. Step 7. Check the I accept the terms of the License Agreement check box and click Next. Step 8. Click the radio button for either: a. Click Next in the Database Options dialog box. Enter a user name and password and click Next. Click Verify to test your login. Click Install if you are installing Fabric Manager Standalone.
Installing Fabric manager on Windows bit Note that Cisco Fabric Manager has not been officially tested on any bit platforms, only bit platforms are officially supported. However users were able to install Fabric Manager on bit Windows by following these steps: Step 1.
Then just follow the steps for the install, as shown in section above. Tags: fabric. Community Member. Can somone please update this link, 64 bit is now supported. Latest Contents.
Created by klopez on AM. Hello, We are in the planning phase for a maintenance window to upgrade the access layer switches in a design very similar to the one below.
I'm curious as to whether or not we need to shut down the VMs that are ru Air Flow Extension Sleeve for Nexus Created by wjlawrence on AM. I have several Nexus 's and I am in need of an Air Flow Extension Sleeve that will deploy in a standard data center cabinet. Looking for Cisco or a third party. Thank you in advance. DNAC Scaling. Created by jeffertz on AM. Hello All, Not sure if this has been answered or not before, but I have not found anything regarding this.
Created by joeharb on PM. New deployment, first FEX that has been introduced. The port channel is configured on the leaf node and the fex is present but it shows Offline. If I shutdown the port it goes from Registering to Offline. Could this be a license issue? Created by Antonio Macia on AM. Using two different L3Outs with two extern Create Content Login to create content. Related Content. Project Gallery.
Content for Community-Ad. This widget could not be displayed. Follow our Social Media Channels.
Installing Fabric Manager.Cisco fabric manager download windows 10
It provides a graphical user interface GUI that displays real-time views of your network fabrics, and lets you manage the configuration of Cisco MDS Family devices and third-party switches. The Cisco Fabric Manager provides an alternative to the command-line interface CLI for most switch configuration commands. In addition to complete configuration and status monitoring capabilities for Cisco MDS switches, Fabric Manager provides powerful Fibre Channel troubleshooting tools.
These in-depth health and configuration analysis capabilities leverage unique MDS switch capabilities: Fibre Channel Ping and Traceroute. The following procedure is a review of the tasks you should have completed during hardware installation, including starting up the switch.
These tasks must be completed before you can configure the switch. Note You must use the CLI for initial switch start up. Tip Save the host ID information for future use for example, to enable licensed features. The host ID information is provided in the Proof of Purchase document that accompanies the switch. Step 2 Verify that the default console port parameters are identical to those of the computer terminal or terminal server attached to the switch console port:.
Step 3 Power on the switch. The switch boots automatically and the switch prompt appears in your terminal window. The first time you access a switch in the Cisco MDS Family, it runs a setup program that prompts you for the IP address and other configuration information necessary for the switch to communicate over the supervisor module Ethernet interface.
This information is required to configure and manage the switch. You cannot change the default user at any time. The setup scenario differs based on the subnet to which you are adding the new switch:. The in-band management feature is transparent to the network management system NMS. The first time that you access a switch in the Cisco MDS Family using the CLI, it runs a setup program that prompts you for the IP address and other configuration information necessary for the switch to communicate over the supervisor module Ethernet interface.
When you power up the switch for the first time, assign the IP address. Before you configure a switch in the Cisco MDS Family for the first time, you need the following information:. Also, provide the IP address of the default network optional. If IP routing is disabled, the switch uses the default gateway IP address. Note You should verify that the Fabric Manager Server hostname entry exists on the DNS server, unless the Fabric Manager Server is configured to bind to a specific interface during installation.
If a password is trivial short, easy-to-decipher , your password configuration is rejected. If you configure and subsequently forget this new password, you have the option to recover this password see the Cisco Fabric Manager Security Configuration Guide.
The setup scenario differs based on the subnet to which you are adding the new switch. Note Some concepts such as out-of-band management and in-band management are briefly explained here. These concepts are explained in more detail in subsequent chapters.
This section describes how to initially configure the switch for both out-of-band and in-band management. Note Press Ctrl-C at any prompt to skip the remaining configuration options and proceed with what is configured until that point.
Entering a new password for the administrator is a requirement and cannot be skipped. Tip If you do not wish to answer a previously configured question, or if you wish to skip answers to any questions, press Enter. If a default answer is not available for example, switch name , the switch uses what was previously configured and skips to the next question.
Note You can configure both in-band and out-of-band configuration together by entering Yes in both Step 11 c and Step 11 d in the following procedure. To configure the switch for first time out-of-band access, follow these steps:.
Step 1 Power on the switch. Step 2 Enter Yes to enforce secure password. Enter the administrator password. Confirm the administrator password. Tip If a password is trivial short, easy to decipher , your password configuration is rejected.
Be sure to configure a secure password as shown in the sample configuration. Passwords are case-sensitive. You must explicitly configure a password that meets the requirements listed in the Cisco Fabric Manager Security Configuration Guide. Step 3 Enter yes to enter the setup mode.
Note This setup utility will guide you through the basic configuration of the system. Setup configures only enough connectivity for management of the system. The setup utility guides you through the basic configuration process. Press Ctrl-C at any prompt to end the configuration process. Step 4 Enter the new password for the administrator admin is the default. Step 5 Enter yes no is the default to create additional accounts. While configuring your initial setup, you can create an additional user account in the network-admin role besides the administrator's account.
Note User login IDs must contain non-numeric characters. Enter the user login ID [administrator]. Enter the user password. Confirm the user password for. Enter the user name admin is the default. Enter the SNMPv3 password minimum of eight characters. The default is admin Enter the SNMP community string. Step 8 Enter a name for the switch. Each switch in the fabric requires a unique name. You can assign names to easily identify the switch by its physical location, its SAN association, or the organization to which it is deployed.
The assigned name is displayed in the command-line prompt. The switch name is limited to 20 alphanumeric characters. Note The switch name is limited to 32 alphanumeric characters. The default is switch. Step 9 Enter yes yes is the default to configure out-of-band management. Enter the mgmt0 IP address. Enter the mgmt0 subnet mask. Step 10 Enter yes yes is the default to configure the default gateway recommended.
Enter the default gateway IP address. Step 11 Enter yes no is the default to configure advanced IP options such as in-band management, static routes, default network, DNS, and domain name. Enter no no is the default at the in-band management configuration prompt. Enter yes no is the default to enable IP routing capabilities. Enter yes no is the default to configure a static route recommended. Enter yes no is the default to configure the default network recommended.
Note The default network IP address is the destination prefix provided in Step 11 c. Enter yes default is no to configure the default domain name. Step 12 Enter yes no is the default to enable Telnet service. Step 13 Enter yes no is the default to enable the SSH service. Step 14 Enter the SSH key type. Step 15 Enter the number of key bits within the specified range.
Step 16 Enter yes no is the default to configure the NTP server. Step 17 Enter noshut shut is the default to configure the default switch port interface to the shut state. Step 18 Enter on on is the default to configure the switch port trunk mode.
Step 19 Enter no no is the default to configure switchport port mode F. Step 20 Enter permit deny is the default to deny a default zone policy configuration. Disables the switch-wide default for the full zone set distribution feature. You see the new configuration. Review and edit the configuration that you have just entered.
Step 22 Enter no no is the default if you are satisfied with the configuration. Step 23 Enter yes yes is default to use and save this configuration:. The in-band management logical interface is VSAN 1. This management interface uses the Fibre Channel infrastructure to transport IP traffic. An interface for VSAN 1 is created on every switch in the fabric. A default route that points to the switch providing access to the IP network should be configured on every switch in the Fibre Channel fabric see Cisco Fabric Manager Fabric Configuration Guide.
Note You can configure both in-band and out-of-band configuration together by entering Yes in both Step 9 c and Step 9 d in the following procedure. Step 2 Enter the new password for the administrator. Tip If a password is trivial short, easy-to-decipher , your password configuration is rejected.
Cisco fabric manager download windows 10.Cisco Fabric Manager
It provides a graphical user interface GUI that displays real-time views of your network fabrics, and lets you manage the configuration of Cisco MDS Family devices and third-party switches. The following procedure is a review of the tasks you should have completed during hardware installation, including starting up the switch.
These tasks must be completed before you can configure the switch. Note You must use the CLI for initial switch start up. Tip Save the host ID information for future use for example, to enable licensed features. The host ID information is provided in the Proof of Purchase document that accompanies the switch. Step 2 Verify that the default console port parameters are identical to those of the computer terminal or terminal server attached to the switch console port:.
Step 3 Power on the switch. The switch boots automatically and the switch prompt appears in your terminal window. The first time that you access a switch in the Cisco MDS Family using the CLI, it runs a setup program that prompts you for the IP address and other configuration information necessary for the switch to communicate over the supervisor module Ethernet interface. This information is required to configure and manage the switch.
When you power up the switch for the first time, assign the IP address. Before you configure a switch in the Cisco MDS Family for the first time, you need the following information:.
Also, provide the IP address of the default network optional. If IP routing is disabled, the switch uses the default gateway IP address. Note You should verify that the Fabric Manager Server hostname entry exists on the DNS server, unless the Fabric Manager Server is configured to bind to a specific interface during installation.
You cannot change the default user at any time see the "Role-Based Authorization" section on page If a password is trivial short, easy-to-decipher , your password configuration is rejected. Be sure to configure a strong password see the "User Accounts" section on page If you configure and subsequently forget this new password, you have the option to recover this password see the "Recovering the Administrator Password" section on page The setup scenario differs based on the subnet to which you are adding the new switch.
Note Some concepts such as out-of-band management and in-band management are briefly explained here. These concepts are explained in more detail in subsequent chapters. The in-band management feature is transparent to the network management system NMS. This section describes how to initially configure the switch for both out-of-band and in-band management.
Note Press Ctrl-C at any prompt to skip the remaining configuration options and proceed with what is configured until that point. Entering the new password for the administrator is a requirement and cannot be skipped. Tip If you do not wish to answer a previously configured question, or if you wish to skip answers to any questions, press Enter.
If a default answer is not available for example, switch name , the switch uses what was previously configured and skips to the next question. Note You can configure both in-band and out-of-band configuration together by entering Yes in both Step 11 c and Step 11 d in the following procedure.
To configure the switch for first time out-of-band access, follow these steps:. Step 1 Power on the switch. Step 2 Enter the new password for the administrator. Tip If a password is trivial short, easy to decipher , your password configuration is rejected.
Be sure to configure a strong password as shown in the sample configuration. Passwords are case-sensitive. You must explicitly configure a password that meets the requirements listed in the "User Accounts" section on page Step 3 Enter yes to enter the setup mode.
The setup utility guides you through the basic configuration process. Press Ctrl-C at any prompt to end the configuration process. Step 4 Enter the new password for the administrator admin is the default.
Step 5 Enter yes no is the default to create additional accounts. While configuring your initial setup, you can create an additional user account in the network-admin role besides the administrator's account. See the "Role-Based Authorization" section on page for information on default roles and permissions.
Note User login IDs must contain non-numeric characters. Enter the user login ID. Enter the user password. Enter the user name admin is the default. Enter the SNMPv3 password minimum of eight characters. The default is admin Enter the SNMP community string. Step 8 Enter a name for the switch. Note The switch name is limited to 32 alphanumeric characters. The default is switch.
Step 9 Enter yes yes is the default to configure out-of-band management. Enter the mgmt0 IP address. Enter the mgmt0 subnet mask. Step 10 Enter yes yes is the default to configure the default gateway recommended. Enter the default gateway IP address.
Step 11 Enter yes no is the default to configure advanced IP options such as in-band management, static routes, default network, DNS, and domain name. Enter no no is the default at the in-band management configuration prompt. Enter yes yes is the default to enable IP routing capabilities. Enter yes yes is the default to configure a static route recommended.
Enter yes yes is the default to configure the default network recommended. Note The default network IP address is the destination prefix provided in Step 11 c. Enter yes default is no to configure the default domain name. Step 12 Enter yes yes is the default to enable Telnet service. Step 13 Enter yes no is the default to enable the SSH service. Step 15 Enter the number of key bits within the specified range.
Step 16 Enter yes no is the default to configure the NTP server. Step 17 Enter noshut shut is the default to configure the default switch port interface to the shut state. Step 18 Enter on on is the default to configure the switch port trunk mode.
Step 19 Enter on off is the default to configure the PortChannel auto-create state. Step 20 Enter permit deny is the default to deny a default zone policy configuration. Step 21 Enter yes no is the default to disable a full zone set distribution see the "Zone Set Distribution" section on page You see the new configuration.
Review and edit the configuration that you have just entered. Step 22 Enter no no is the default if you are satisfied with the configuration. Step 23 Enter yes yes is default to use and save this configuration:. The in-band management logical interface is VSAN 1. This management interface uses the Fibre Channel infrastructure to transport IP traffic. An interface for VSAN 1 is created on every switch in the fabric.
Note You can configure both in-band and out-of-band configuration together by entering Yes in both Step 9 c and Step 9 d in the following procedure.
Tip If a password is trivial short, easy-to-decipher , your password configuration is rejected. Step 4 Enter no no is the default if you do not wish to create additional accounts. Enter no no is the default to avoid configuring the read-only SNMP community string. Enter no no is the default to configure the read-only SNMP community string.
Step 6 Enter a name for the switch. Step 7 Enter no yes is the default at the configuration prompt to configure out-of-band management. Step 8 Enter yes yes is the default to configure the default gateway. Step 9 Enter yes no is the default to configure advanced IP options such as in-band management, static routes, default network, DNS, and domain name.
Enter yes no is the default at the in-band management configuration prompt. Enter no yes is the default to enable IP routing capabilities.
Enter no yes is the default to configure a static route. Enter no yes is the default to configure the default network. Enter no no is the default to skip the default domain name configuration.
Step 10 Enter no yes is the default to disable Telnet service. Step 11 Enter yes no is the default to enable the SSH service. Step 13 Enter the number of key bits within the specified range.
Comments
Post a Comment